#1 2009-10-31 17:43:27
ASUS RT-N16台灣正式發售版開箱報告
昨天大嘴鳥叼來一箱東西....
拆開一看....
口圭~~這不是站長說的怪獸嗎??
讚~~來看看東西吧~~
看看背面..
兩側..
內容物(未全拆)
內容物(全拆)
大家好奇的....裡面長什麼樣....
抱歉..這顆不是CPU....CPU是散熱片下的那一顆....
RAM....BGA封裝....要升級恐怕有一定難度....
拍攝工具：
NIKON D90+Sigma 24mm F1.8 Macro
女王回來了....快閃....
待續....
最後修改： hannahmo (2009-10-31 22:53:48)
離線
#2 2009-10-31 18:23:01
Re: ASUS RT-N16台灣正式發售版開箱報告
趁吃飯時間....繼續....
系統內資訊....
# cat /proc/cpuinfo
system type : Broadcom BCM4716 chip rev 1
processor : 0
cpu model : MIPS 74K V4.0
BogoMIPS : 238.59
wait instruction : no
microsecond timers : yes
tlb_entries : 64
extra interrupt vector : no
hardware watchpoint : yes
ASEs implemented : mips16 dsp
VCED exceptions : not available
VCEI exceptions : not available
unaligned_instructions : 2
dcache hits : 2147483648
dcache misses : 3488175871
icache hits : 2147483648
icache misses : 3735769009
instructions : 2147483648
# cat /proc/meminfo
MemTotal: 126336 kB
MemFree: 103188 kB
Buffers: 3872 kB
Cached: 7972 kB
SwapCached: 0 kB
Active: 4024 kB
Inactive: 9552 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 1740 kB
Mapped: 1552 kB
Slab: 4672 kB
SReclaimable: 1152 kB
SUnreclaim: 3520 kB
PageTables: 360 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
CommitLimit: 63168 kB
Committed_AS: 4284 kB
VmallocTotal: 786388 kB
VmallocUsed: 3972 kB
VmallocChunk: 781400 kB
# cat /proc/version
Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.1.2) #153 Tue Jun 23 16:25:53 CST 2009
# uname -a
Linux (none) 2.6.22 #153 Tue Jun 23 16:25:53 CST 2009 mips unknown
# cat /tmp/syslog.log
Jan 1 00:00:05 (none) syslog.info syslogd started: BusyBox v1.7.2
Jan 1 00:00:05 (none) user.notice igmp[1820]: igmp started!
Jan 1 00:00:10 (none) user.emerg dhcp client: deconfig: lease is lost
Jan 1 00:00:11 (none) user.notice igmp[1820]: setsockopt- MRT_ADD_VIF
Jan 1 00:00:11 (none) user.notice igmp[1820]: interface 192.168.1.1, DOWNSTREAM ver=0x16 name=br0 index=7
Jan 1 00:00:11 (none) user.notice igmp[1820]: interface 0.0.0.0, UPSTREAM ver=0x16 name=eth0 index=4
Jan 1 00:00:12 (none) user.emerg WAN Connection: The cable for Ethernet was not plugged in.
Jan 1 00:00:13 (none) user.notice igmp[1820]: igmp:IP_ADD_MEMBERSHIP Failed
Jan 1 00:00:46 (none) daemon.info utelnetd[1906]: utelnetd (port: 23, ifname: any, login: /bin/sh) startup succeeded
Jan 1 00:01:14 (none) daemon.info utelnetd: connection from: 192.168.1.2
接下來....特別注意藍色部份..這與之前hippo前輩拿到的版本不一樣....高了一點點....
# dmesg
Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.1.2) #153 Tue Jun 23 16:25:53 CST 2009
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
On node 0 totalpages: 32767
Normal zone: 255 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126064k/131068k available (2771k kernel code, 4856k reserved, 564k data, 124k init, 0k highmem)
Calibrating delay loop... 238.59 BogoMIPS (lpj=119296)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Fixing up bridge
PCI: Setting latency timer of device 0000:01:00.1 to 64
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.4 (2008/08/26) Phillip Lougher
NTFS driver 2.1.28 [Flags: R/O].
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.2
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Physically mapped flash: squashfs filesystem found at block 1816
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "boot"
0x00040000-0x01fe0000 : "linux"
0x001c63f8-0x01fe0000 : "rootfs"
0x01fe0000-0x02000000 : "nvram"
Found a 0MB serial flash
sflash: found no supported devices
GACT probability NOT on
Mirror/redirect action on
netem: version 1.2
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1023 buckets, 8184 max)
ctnetlink v0.93: registering with nfnetlink.
ipt_time loading
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ipgre init: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear
All bugs added by David S. Miller
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Warning: unable to open an initial console.
emf: module license 'unspecified' taints kernel.
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.27
PCI: Setting latency timer of device 0000:00:01.0 to 64
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.27
Algorithmics/MIPS FPU Emulator v1.5
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: add 33:33:ff:2c:8b:9c mcast address to master interface
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
dbg: usb init
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB20H mdio control register : 0x80000018
PCI: Setting latency timer of device 0000:00:04.1 to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB20H mdio control register : 0x80000018
PCI: Setting latency timer of device 0000:00:04.0 to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ufsd: no version for "struct_module" found: kernel tainted.
ufsd: driver loaded at c024d000 built on Mar 5 2009 13:51:35
UFSD version 7.02 (Mar 5 2009, 13:50:00)
NTFS read/write support included
$Id: ufsdvfs.c,v 1.195 2009/02/02 15:38:06 shura Exp $
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
vlan1: del 33:33:ff:2c:8b:9c mcast address from vlan interface
vlan1: del 33:33:ff:2c:8b:9c mcast address from master interface
vlan1: del 01:00:5e:00:00:01 mcast address from vlan interface
vlan1: del 01:00:5e:00:00:01 mcast address from master interface
vlan1: del 33:33:00:00:00:01 mcast address from vlan interface
vlan1: del 33:33:00:00:00:01 mcast address from master interface
br0: port 1(vlan1) entering disabled state
vlan1: dev_set_promiscuity(master, 1)
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 33:33:ff:2c:8b:9c mcast address to master interface
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
[k] track_flag=0, clean_flag=101, ipaddr=0
eth1: no IPv6 routers present
[k] track_flag=0, clean_flag=100, ipaddr=0
br0: no IPv6 routers present
httpd uses obsolete (PF_INET,SOCK_PACKET)
vlan1: no IPv6 routers present
eth0: no IPv6 routers present
以上....開箱完畢....
網頁設定相關畫面....
請參考hippo前輩的怪獸機 ASUS RT-N16 開箱報告
感謝大家....
離線
#3 2009-10-31 22:31:11
Re: ASUS RT-N16台灣正式發售版開箱報告
哇..感謝您冒著婚姻幸福美滿的風險，為大家拆機拍裸照 
# dmesg
Linux version 2.6.22 (root@localhost.localdomain) (gcc version 4.1.2) #153 Tue Jun 23 16:25:53 CST 2009
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
On node 0 totalpages: 32767
Normal zone: 255 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
...
所以正式出貨是以 480Mhz 的時脈速度，跟原來公佈的 533Mhz 還是有一小段的落差。
上次小試過超頻至 533Mhz，效能有提升一點，不過風險請自負。
# nvram set clkfreq=532,266,133
# nvram commit
# reboot技術問題請於論壇上集眾人之力公開討論，感恩
離線
#4 2009-10-31 22:52:33
Re: ASUS RT-N16台灣正式發售版開箱報告
嗯....
超到533的話....
我怕散熱有問題....
雖然它CPU上有一塊散熱片....
不過....我還真想換掉它....再加上一顆小風扇....
這樣好像太機車....哈....
有空先來備份CFE....
再來玩....
搞熟原廠韌體後....
再來考慮要不要直上x-wrt....
剛剛去看了openwrt 8.09有支援BCM47XX....
只是....上openwrt....後續好像有一點難度....
再看看....
看有沒有那一家要先出N16的韌體....
離線
#5 2009-10-31 23:07:55
Re: ASUS RT-N16台灣正式發售版開箱報告
這2顆RAM....
DDR2 64MB*2
DATASHEET如底下連結....
有興趣的看看吧....
http://www.datasheetdir.com/K4N51163QZ-HC25+DDR2-SDRAM
離線
#8 2009-11-02 21:38:57
Re: ASUS RT-N16台灣正式發售版開箱報告
官方又釋出一版 ASUS RT-N16 測試版韌體，版本是 9.9.3.7 (2009/10/22 更新)
不知道有沒有人試過?
http://support.asus.com/download/downlo … del=RT-N16
技術問題請於論壇上集眾人之力公開討論，感恩
離線
#9 2009-11-03 22:41:37
Re: ASUS RT-N16台灣正式發售版開箱報告
報告站長..
因為我對官方韌體沒什麼大興趣....
所以我也沒去試....
另外....
ASUS這次就感心....
TTL的針腳預焊好了....
直接插上去就可以用了....
我測試了一下....連接環境如下：
Baud Rate:115200
Parity:None
Data bits:8
Stop bits:1
Flow Control:None
接上TX/RX/GND三腳....
就可以順利連上觀看資訊....
目前大致玩了它原廠1.0.0.6版的韌體....
設定網頁上的BUG蠻多的....
寫的不太好....
常常設定好按下確認後....
會停在確認中的畫面....
都要RELOAD....有時候設定還會沒存進去....
要再重設....
所以目前這台沒有被我拿來放在線上使用....
都只是拿來亂搞....
已經COMPILE三次OPENWRT了....都不能用....
暫時等等吧....
最後修改： hannahmo (2009-11-03 22:42:04)
離線
相關討論主題
| 主題 | 回覆 | 點閱 | 最後發表 |
|---|---|---|---|
|
ASUS RT-N66U刷Shibby 140 MultiWAN後設定為無線AP 作者 lcjh20516
|
0 | 2388 | 2022-08-26 12:56:28 作者 lcjh20516 |
|
|
159 | 386032 | 2022-08-14 06:06:27 作者 lcjh20516 |
|
|
21 | 83760 | 2022-08-14 05:54:54 作者 lcjh20516 |
|
置頂 |
132 | 375085 | 2022-06-07 10:13:50 作者 dennys |
|
|
45 | 140520 | 2022-05-06 14:32:17 作者 max7441 |
