====== Console ====== J5: (1)3.3V (2)Tx (3)Rx (4)GND +Ethernet eth0: MAC address 00:11:6b:xx:xx:xx IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1 Default server: 0.0.0.0, DNS server IP: 0.0.0.0 RedBoot(tm) bootstrap and debug environment [ROMRAM] Red Hat certified release, version 1.92 - built 15:16:07, Feb 3 2004 Platform: IXDP425 Development Platform (XScale) Copyright (C) 2000, 2001, 2002, Red Hat, Inc. RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each. == Executing boot script in 2.000 seconds - enter ^C to abort RedBoot> boot;exec 0x01d00000 have eRcOmM copy kernel code from flash to RAM copy ramdisk file from flash to RAM run kernel Using base address 0x01d00000 and length 0x000f9088 Uncompressing Linux.................................................................... done, booting the kernel. Linux version 2.4.22-xfs (root@localhost.localdomain) (gcc version 3.2.1) #617 Tue Jul 11 13:05:07 CST 2006 CPU: XScale-IXP425/IXC1100 revision 1 Machine: Intel IXDP425 Development Platform Warning: bad configuration page, trying to continue Security risk: creating user accessible mapping for 0x60000000 at 0xff00f000 Security risk: creating user accessible mapping for 0x51000000 at 0xf1000000 Security risk: creating user accessible mapping for 0x54000000 at 0xf4000000 Security risk: creating user accessible mapping for 0x55000000 at 0xf5000000 Security risk: creating user accessible mapping for 0x56000000 at 0xf6000000 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0,115200 root=/dev/ram0 initrd=0x01000000,14M mem=32M@0x00000000 Calibrating delay loop... 266.24 BogoMIPS Memory: 32MB = 32MB total Memory: 15828KB available (1701K code, 270K data, 244K init) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX We need delay 20 seconds to let BIG HDD ready smoothly. PCI Autoconfig: Found Bus 0, Device 1, Function 0 PCI Autoconfig: BAR 0, I/O, size=0x20, address=0xffffffe0 PCI Autoconfig: Found Bus 0, Device 1, Function 1 PCI Autoconfig: BAR 0, I/O, size=0x20, address=0xffffffc0 PCI Autoconfig: Found Bus 0, Device 1, Function 2 PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffff00 PCI Autoconfig: Found Bus 0, Device 4, Function 0 PCI Autoconfig: BAR 0, I/O, size=0x8, address=0xffffffb8 PCI Autoconfig: BAR 1, I/O, size=0x4, address=0xffffffb4 PCI Autoconfig: BAR 2, I/O, size=0x8, address=0xffffffa8 PCI Autoconfig: BAR 3, I/O, size=0x4, address=0xffffffa4 PCI Autoconfig: BAR 4, I/O, size=0x80, address=0xffffff00 PCI Autoconfig: BAR 5, Mem, size=0x1000, address=0x4bffe000 PCI: bus0: Fast back to back transfers disabled PCI: Via IRQ fixup for 00:01.0, from 28 to 12 PCI: Via IRQ fixup for 00:01.1, from 27 to 11 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Disk quotas vdquot_6.5.1 SGI XFS with no debug enabled SGI XFS Quota Management subsystem i2c-core.o: i2c core module i2c-dev.o: i2c /dev entries driver module i2c-core.o: driver i2c-dev dummy driver registered. i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xff000003 (irq = 15) is a XScale UART ttyS01 at 0xff001003 (irq = 13) is a XScale UART RAMDISK driver initialized: 16 RAM disks of 14336K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx AEC6280: IDE controller on PCI bus 00 dev 20 AEC6280: chipset revision 16 AEC6280: not 100% native mode: will probe irqs later AEC6280: Make sure ROM is disabled ide0: BM-DMA at 0xffffff00-0xffffff07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffffff08-0xffffff0f, BIOS settings: hdc:pio, hdd:pio hda: ST340014A, ATA DISK drive ide0 at 0xffffffb8-0xffffffbf,0xffffffb6 on irq 25 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx blk: queue c022f514, no I/O memory limit hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(66) Partition check: hda: hda1 hda2 hda3 SCSI subsystem driver Revision: 1.00 * host: cfi_cmdset_0001: Erase suspend on write enabled Using buffer write method Using static MTD partitions. Creating 4 MTD partitions on "IXP425 Flash": 0x00000000-0x00040000 : "RedBoot " 0x00040000-0x00060000 : "System Configuration" 0x00060000-0x00160000 : "Kernel" 0x00160000-0x00800000 : "Ramdisk" usb.c: registered new driver hub pci probe begin ehci_hcd 00:01.2: VIA Technologies, Inc. USB 2.0 ehci_hcd 00:01.2: irq 26, pci mem 4bffff00 usb.c: new USB bus registered, assigned bus number 1 IXP425_GPIO_GPIT1R:35b000, IXP425_GPIO_GPIT2R:36c9 PCI: 00:01.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:01.2 PCI cache line size corrected to 32. ehci_hcd 00:01.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 4 ports detected pci probe ok host/usb-uhci.c: $Revision: 1.4 $ time 13:05:27 Jul 11 2006 host/usb-uhci.c: High bandwidth mode enabled host/usb-uhci.c: USB UHCI at I/O 0xffffffe0, IRQ 26 host/usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected host/usb-uhci.c: USB UHCI at I/O 0xffffffc0, IRQ 26 host/usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb.c: registered new driver usblp printer.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. i2c-dev.o: Registered 'IXP425 I2C Adapter' as minor 0 i2c-core.o: adapter IXP425 I2C Adapter registered as adapter 0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NetWinder Floating Point Emulator V0.97 (double precision) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 14336K VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 244K init started: BusyBox v0.60.4 (2006.07.05-08:18+0000) multi-call binary -------------------------------Begin in rc------------------------------ Insmod ixp400 Using /lib/modules/2.4.22-xfs/ixp400.o Warning: loading ixp400 will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module init. Insmod ixp425 Using /lib/modules/2.4.22-xfs/ixp425_eth.o ixp425_eth: Initializing IXP425 NPE Ethernet driver software v. 1.1 ixp425_eth: CPU clock speed (approx) = 0 MHz [error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201 ixp425_eth: ixp0 is using the PHY at address 1 ixp425_eth: ixp1 is using the PHY at address 0 Please press Enter to activate this console. Creating ramfs for /var/lock/samba: Limit the space of log folder: Starting Hostname : OK Starting Modules : ixp425_eth: ixEthMiiLinkStatus failed on PHY0. Can't determine the auto negotiated parameters. Using default values. Using /lib/modules/pbuttons.o Using /lib/modules/rbuttons.o Using /lib/modules/x1226-rtc.o S3530: I2C based RTC driver. i2c-core.o: driver S3530 registered. S3530: RTC is S-3530A S3530: found s3550 on IXP425 I2C Adapter i2c-core.o: client [S3530] registered to adapter [IXP425 I2C Adapter](pos. 0). begin in bt_interrupt(). jiffies is <2990> r_ok_time is <2990> end of bt_interrupt() Using /lib/modules/usbbuttons.o insmoding ufsd.o Using /lib/modules/ufsd.o Warning: loading ufsd will taint the kernel: non-GPL license - Commertial product See http://www.tux.org/lkml/#export-tainted for information about tainted modules Using /lib/modules/nls_cp932.o Using /lib/modules/nls_cp936.o Using /lib/modules/nls_cp950.o ufsd: driver loaded UFSD version 5.11 (Jul 25 2005, 15:26:54) New NTFS read/write support included Format NTFS included Extend NTFS included Using /lib/modules/nls_cp949.o Starting Set CGI_ds.conf: ip_addr<192.168.0.100> udhcp client (v0.9.6) started Sending discover... Sending discover... Sending discover... Sending select for 192.168.20.127... Lease of 192.168.20.127 obtained, lease time 86400 killall: udhcpd: no process killed XFS mounting filesystem ide0(3,1) XFS mounting filesystem ide0(3,2) valid_num[0] is <1> nvalid_num[0] is <0>. valid_num[FIRST_DSK] is <1> valid_num[SECOND_DSK] is <0>. Setting up swapspace version 0, size = 131600384 bytes Adding Swap: 128516k swap-space (priority -1) OK Starting Set HDD parameters : OK Restore time and timezone: Sat Jan 1 00:00:39 2000 OK Restore usrgrpshares: OK Generating telnet password: pwd is . OK Starting WEB Server: OK OK Starting CUPS : Starting download: download uses obsolete (PF_INET,SOCK_PACKET) Creating ramfs for /tmp: Starting Crond : Starting samba: Starting Rest Task : FNS-1000: boot complete! OK Starting QuickSet Daemon : OK OK Checking disk status : Remove modules : OK ====== Optware ====== [[http://digiland.tw/viewtopic.php?pid=5028|LevelOne FNS-1000]]